![]() ![]() Parameters | Eraser tool | Paint Bucket | Gradient tool.Parameters | Zoom tool | Rectangle tool.Display mode | Palette | File | Window | Layers | Object.And don't get me wrong, they normally do this is just one tiny oversight that I found purely by accident when I was playing around. Generally I try to think of Scribus as a layout tool with some useful in-built graphics capabilities, but I'd like to hope that those graphics capabilities work properly when I use them. Like you, I do most of my more complex vector graphics - and mine aren't that complicated I have to say - in Inkscape too. start the rotation calculation at the object's current rotation angle instead of zero - but it's little details like this that could make newbies wary of using what is an otherwise excellent piece of software. It's probably a very simple programming change - i.e. Unless, of course, someone can tell me why I am wrong. I can't think of any reason why it should work as it currently does and I've never seen that in any other application. Making a duplicate by rotation, in my view, should take the current rotation of the object into account as its starting point. However, I think that the issue raised in Figure 4 is something that should be looked at as a bug. Maybe someone can think of a good compromise? I have a feeling that this particular issue is a long-haul debate where either side is as valid as the other but in different ways. I can see positives and negatives to each method too. I think you're right about my question not being easy to answer. But what does everyone else think? Is it just me being stupid or picky or am I on to something here? Tell me what you think. Personally I think it should use the shape's current rotation as a starting point as it seems more natural and expected. ![]() my question to the rest of the forum is this: "Should Scribus take the current rotation of a shape into account as a starting point when rotating, or should it use the shape's original orientation?" If you know you're going to be rotating things, plan ahead and make sure you know what you're doing.Īnd. after all that, my "friendly warning" to people is to be careful when rotating things as the results may not be how you might naturally expect. Then I duplicated/rotated the shape and finally got my flower shape. Then I changed the rotation base-point to the bottom-left. So, then I modified the original shape so that its pointy end was at the corner of the bounding box. After some thought this seems reasonable but maybe not what could be expected as I've used other software that works differently - that could just be my unreasonable expectations though. On top of this, the bounding box of the shape stays in the same orientation as the shape rather than the box "reorganising itself" to be a different shape but in the horizontal/vertical axes. ![]() They're the same as in Figure two but start in the "wrong" place because of the earlier rotation. What had happened was that the shape was still rotated around the top-left-hand corner of the bounding box but that corner was now at the right of the shape, and Scribus still thinks that the top-left-hand corner of the frame is at the top-left-hand of the shape so it starts rotating from that position which is why the rotated shapes are where they are. Then I tried the rotation again, and the results were worse. This showed me that the duplicates had been rotated around the top-left-hand corner of the frame the shape is in (as is default and shown in the XYZ section of the Properties palette, as pictured).Īll that sounds fine and is how it should be but it obviously this wasn't what I wanted so I thought I'd rotate the shape - by 225 degrees - to make its pointy end at the top-left corner, as in Figure 3. However that wasn't as easy as I thought it might be.įirst, as a test, I tried to create two duplicates rotated by 20 degrees. My expectation was that I could duplicate/rotate (menu "Item -> Multiple Duplicate") it about the pointy end to create the "face" of a flower. I was trying to draw a simple flower - don't me ask why - and I started with a simple petal. And after a bit of experimenting I thought I'd share some of my experiences. I was messing around with the Scribus rotation tools recently - I don't use them very much - and found that they didn't work in the way I thought they might. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |